Search found 90 matches
- March 21st, 2023, 4:10 pm
- Forum: WTB: Want to buy
- Topic: wheels for a New Era stadium truck
- Replies: 4
- Views: 2216
Re: wheels for a New Era stadium truck
What size and style you need?
- October 20th, 2022, 5:10 am
- Forum: WTB: Want to buy
- Topic: Stamped steel wheels
- Replies: 11
- Views: 3228
Re: Stamped steel wheels
The standard for wheels is best to start with. You can make wheel covers to simulate what you're trying to do. Easier than destroys something that isn't rite from the start. You can also look at castor wheels as an option or medical supply wheels. But for what you want best; just make them.
- October 19th, 2022, 4:50 am
- Forum: WTB: Want to buy
- Topic: Stamped steel wheels
- Replies: 11
- Views: 3228
Re: Stamped steel wheels
The center of the wheel is not what you think. The front has a bearing between two pressed half's and the rear has a bushing to drive the rear wheels. You will not be able to do what you think. Better off making your wen style wheels that fit pin hubs. Wcm made 1/2" wheels halfs and Bishracing ...
- October 18th, 2022, 7:28 am
- Forum: WTB: Want to buy
- Topic: Stamped steel wheels
- Replies: 11
- Views: 3228
- March 18th, 2022, 5:29 pm
- Forum: Car Discussion
- Topic: Skellenger gears please help
- Replies: 5
- Views: 2037
Re: Skellenger gears please help
Gears came in two thickness. 1/4" to reduce weight and to get more gears from bar stock and original 3/8*" Both styles were heat treated.
- March 18th, 2022, 5:17 pm
- Forum: Car Discussion
- Topic: Skellenger gears please help
- Replies: 5
- Views: 2037
Re: Skellenger gears please help
That's not a pile of gears? Looks like 5 matching sets? !3/27- 19-21 is the range. If gears are 1/4" thick you will need the 1/8 " spacers.
- February 27th, 2022, 9:34 am
- Forum: WTB: Want to buy
- Topic: Wcm axle pulley needed HELP!!!!!!
- Replies: 3
- Views: 878
Re: Wcm axle pulley needed HELP!!!!!!
If it has the timing pulley: I haven't figure it out either. I can get the clutch shoe off but the clutch drum is welded on to the shaft on other side. I would just heat the clutch with a torch and the braze weld will come off: If tig welded then it will require a bit more work. If you do figure out...
- February 27th, 2022, 7:15 am
- Forum: WTB: Want to buy
- Topic: Wcm axle pulley needed HELP!!!!!!
- Replies: 3
- Views: 878
Re: Wcm axle pulley needed HELP!!!!!!
I converted all mine to ball diff drive. I could use more too. I have been looking for a long time. Chain drive would be easier.
- February 25th, 2022, 5:29 am
- Forum: WTB: Want to buy
- Topic: Zenoah engine to drive shaft
- Replies: 1
- Views: 759
Re: Zenoah engine to drive shaft
A j-joint.
- February 16th, 2022, 5:51 am
- Forum: Car Discussion
- Topic: Need some pointers.. old WCM Grand National
- Replies: 13
- Views: 4035
Re: Need some pointers.. old WCM Grand National
WOW. What what holding the motor? I never seen one with chain at the motor? NO gear adjustment like the timing belt? I had one 1/4' plate with one mounting hole and my others has two holes. So, I drill the two hole's and moved the motor back and they lined up to use the shorter belt. I replace all t...
- February 15th, 2022, 2:50 pm
- Forum: Car Discussion
- Topic: Need some pointers.. old WCM Grand National
- Replies: 13
- Views: 4035
Re: Need some pointers.. old WCM Grand National
On the timing belt side you will see a 1/4" plate bolting the motor to the chassis. From the back of that plate to the back of the frame should be 3-3/8". If the holes line up then your good to go with the shorter belt. The front is fine.
- February 15th, 2022, 11:13 am
- Forum: Car Discussion
- Topic: Need some pointers.. old WCM Grand National
- Replies: 13
- Views: 4035
Re: Need some pointers.. old WCM Grand National
Yes but it depends if there are original old holes behind the motor that will line up with shorter belt? I had one car that had the motor mounted forward but I had two to compare to so I could move the motor back.
- February 15th, 2022, 5:50 am
- Forum: Car Discussion
- Topic: Need some pointers.. old WCM Grand National
- Replies: 13
- Views: 4035
Re: Need some pointers.. old WCM Grand National
The correct way was to mount a idler pully to lift the belt over the frame. Or add additional crossmember in front of the cut out to brace the frame. The stock drive belt was a 3L260 which moves the motor back closer to the rear wheels.
- February 14th, 2022, 6:00 am
- Forum: Car Discussion
- Topic: Need some pointers.. old WCM Grand National
- Replies: 13
- Views: 4035
Re: Need some pointers.. old WCM Grand National
The motor appears to be mounted further forward to provide better steering. I have the same fame but with the ball diff for better cornering. Cutting the fame to allow the belt to pass????? I would move the motor back to the stock location holes if there still there and fix the space. You don't want...
- February 10th, 2022, 5:46 am
- Forum: WTB: Want to buy
- Topic: 1/4 SCALE NEW ERA STADIUM TRUCK CARBURETOR
- Replies: 2
- Views: 966
Re: 1/4 SCALE NEW ERA STADIUM TRUCK CARBURETOR
A model number would help?