Quickdraw tuned pipes

Lovedr · Post by **Lovedr** » December 22nd, 2006, 2:35 pm

I want that truck!!!!!

Post by **Mike Casey** » December 22nd, 2006, 2:45 pm

Here are a couple more off topic pics of the ST. I cant sell it. I cant sell anything

Lovedr · Post by **Lovedr** » December 22nd, 2006, 8:37 pm

what kind of rear end do you bhave in that thing

Post by **Mike Casey** » December 22nd, 2006, 10:27 pm

It is an original QRS rear that someone took the gears out of and machined a new housing.

quickdraw · Post by **quickdraw** » December 22nd, 2006, 11:41 pm

QSL and Fred
Looking for the chassis parts for the GN. I usually get home at 11:00 at night. Been major cold when I get home to go out and look. So when I do it isn't for long. Been running like between 15 and 25 degrees at night here. Plus we had some snow and supposed to get hit again. They say should be ok on Saturday, so I am going to look than. I have come across alot of the parts and gathering parts for the cars.
QSL
The chassis you have are the light weight sprinters we built. I do notice only one car has the reinforcement bars in it. These helped quit abit in an accident.
Fred
I will try again now to email you on the pipes. See what happens.
Todd

alloyparts · Post by **alloyparts** » December 23rd, 2006, 4:41 am

Thanks Todd,
for whatever reason, I am not getting the email, try to pm me and see if that works
Merry Christmas to all
Fred

quickdraw · Post by **quickdraw** » December 23rd, 2006, 4:51 am

Fred
PM sent...see what happens

Post by **Mike Casey** » December 23rd, 2006, 9:36 am

Todd, you are a madman.... 11 at night, wicked cold out? Under those conditions it would take me years to look for something.

alloyparts · Post by **alloyparts** » December 23rd, 2006, 12:47 pm

Got it Todd, Thanks pm sent to you as well.

quickdraw · Post by **quickdraw** » December 23rd, 2006, 3:15 pm

QSL
Yeah, usually 7 days a week. I usually start at 8-9:00 am and get off at 11:00 pm. Small company so you do what you can to survive. Was checking board now. On break and going to look for parts.
See what happens and keep you posted
Another thing funny too. Everyone thinks California is down in the LA area. Think the weather is all the same throughout CA. We had customers call us on and off that they were visiting in LA area and wanted to stop by. When we tell them it is like 10 hrs away. They say no way not going that far. Nice in some ways bad in others. Just have to deal with the weather is all in the mountains.

quickdraw · Post by **quickdraw** » December 27th, 2006, 12:00 am

Fred
No way to do pics in pm. So I put it here. Will get back too you on the rest of your pm there. The 90 deg. aluminum block shown in the pic is what you would have to make.
Fred and QSL
Also looking for parts still and having good luck on the GN. Will keep digging for the parts.
Lance
Still looking for the chassis. I know it's here somewhere, just where. Typical...you don't need it, you find it. Then when you need it, you can't find it.
Todd

big maestro · Post by **big maestro** » December 27th, 2006, 3:12 pm

Todd, I know exactly what your talking about. If you have enough parts to do another GN I would be interested in one of those as well. How about the pipe for the PRC car. Do you already have one made or do you need to make it? I am sending my frame to get powder coated in a few days, cant wait to put that car back together. I am also going to need one of the pipes like the one on the link I put on here for the K car.
Thanks, Lance
Also, check your PM when you get a chance.

quickdraw · Post by **quickdraw** » December 27th, 2006, 11:23 pm

Guys
These pipes are no longer available.
Raco GN/Outlaw/Rabbit (Also believe it fits the truck too but can't remember if it fits under bed ok)
Raco Sidewinder
Wcm Belt sprinter

Larry Cross ordered what I had remaining for his cars. The same body was used to build all these pipes
The QD sprint, super and PRC gn all use the QD sprint body. I still have alot of these on hand.
Lance.
Maybe we can see if we can cut and turn a sprint car pipe tp fit into your car to make it work? Worth a shot. I have the fixture for the location of routing on the K car and can see if somehow I can get a sprint body to fit in. The PRC pipe I will need to weld up. I will be working on Larry's pipe this weekend. I can see about trying to wedge it in also, but I have a lot of pipes to weld up.
Todd

big maestro · Post by **big maestro** » December 30th, 2006, 7:10 pm

Todd, No rush whats so ever. As long as I know you have the stuff I'm cool. Just don't forget about my super

. Just when you get a chance I'm not going anywhere. Believe me I know how the "there's never enough hours in a day" thing
Have a good new year.
Lance

maddog · Post by **maddog** » September 29th, 2009, 7:36 am

i know this was a old tread but idd like to know if or where i can get hold of a QD pipe for a sprintcar.?. i enny one can help me out cheers...or enny info on them.....

www.Quarterscalelegends.com

The awesome history of 1/4 scale!

Quickdraw tuned pipes

Re: Quickdraw tuned pipes